![curl_easy_perform fails borland c++ builder curl_easy_perform fails borland c++ builder](https://www.alfasoft.com/images/products/embarcadero/radstudio/images/v11/Whats_new_images/11preview_01-2048425.png)
- Curl_easy_perform fails borland c++ builder code#
- Curl_easy_perform fails borland c++ builder series#
When calibrating the eTape, keep in mind that it is a pressure sensitive sensor, and so any holding or touching along the measurement surface can disrupt measurements.
Curl_easy_perform fails borland c++ builder code#
Again, Python code used for testing can be downloaded below.Īll 3 devices worked as intended, and reported measurements through a LabJack without issue. Usually something in the range of 1.8k to 4.7k will work, but SRF02 documentation stated that 1.8k are optimal. When using I2C remember to pull SDA and SCL high through a resistor. It is shown below connected to a U3 via I2C. The SRF02 is an ultrasonic sensor similar to the EZ0 but it only offers Serial, and I2C output. The Python code used in testing the device can be downloaded below. When 5V is connected the conversion is approximately. It can be connected directly to any port on a LabJack configured for analog and report a voltage corresponding to a distance.Ĭonnect the AN output of the EZ0 to any of the FIO ports on the LabJack U3 and measure range by converting the voltage to inches. The LV-MaxSonar-EZ0 is a very easy to use ultrasonic sensor made by MaxBotix Inc. In general a narrow beam width will have lower sensitivity than a wide beam width.įor more information on beam width, this is a helpful explanation from MaxBotix. Sensor manufactures commonly report this path in terms of beam width because it is possible to measure distance in a smaller path by using a narrower beam width although beam width on its own describes the angle of the sonar wave as it propagates toward an object. When using ultrasonic type sensors it is important to consider the unobstructed path required for accurate distance measurement. LabJacks are capable of handling any of these data formats, but Analog and I2C are the only types discussed in this App Note.
![curl_easy_perform fails borland c++ builder curl_easy_perform fails borland c++ builder](https://www.matrix-vision.com/manuals/SDK_C/cmake.generatedSolution.png)
They can provide the range information in a variety of data formats, such as PWM, Serial, I2C, or Analog output. They are commonly employed in robotics for obstacle detection, and are useful in many other applications. In the range of 1 to 25 feet, these sensors are well suited for range/depth measurement. The Python code used in gathering data can be downloaded below. See voltage divider section of the eTape datasheet for more details.
Curl_easy_perform fails borland c++ builder series#
When using these sensors there are several options for wiring, the simplest of which is to use it in series with another resistor as a simple potentiometer. The immersed sensor and wiring is shown below. The eTape was tested in a 250 ml graduated cylinder, and reported the depth of liquid readily after software calibration. It provides a varying resistance that is pretty easy to work with. It is made by Milone Technologies and can be manufactured in custom lengths to fit any application. The PN-6573P-12 eTape sensor is a solid state, continuous fluid level sensor for measuring levels in water, non-corrosive water based liquids and dry fluids (powders). Note that a DC signal does not mean you can't do dynamic measurements, it just means that the movement signal is not riding on a carrier frequency. That could mean an LVDT with built-in electronics, or it could mean an external signal conditioner that works with a raw AC-AC LVDT to excite it and provide a simple DC output signal. The AC signal is likely possible to read with a LabJack, but it depends on the details and is not simple. The AC excitation is difficult if not impossible to directly provide from a LabJack. A true LVDT is a linear variable differential transformer, and a raw LVDT requires AC input excitation and provides an AC signal (AC-AC LVDT). The term LVDT is sometimes used for any displacement sensor, but in fact is a specific type of displacement sensor. Sharp), draw-wire, LVDT, capacitive, inductive, eddy-current, and laser. Other sensors for measuring distance/displacement include infrared (e.g. It is important to consider beam width and communication protocol that will work with your application when choosing an ultrasonic sensor, since manufacturers provide a variety of beam widths and protocols. Ultrasonic sensors are good at measurements in the range of several feet with a somewhat unobstructed path to the object in question. Hydrostatic sensors are best for measuring in the range of a few inches in depths of liquids or some powders.
![curl_easy_perform fails borland c++ builder curl_easy_perform fails borland c++ builder](https://i.ytimg.com/vi/OEsw6juLg-I/maxresdefault.jpg)
Two basic types of sensors covered in this app note: hydrostatic and ultrasonic.
![curl_easy_perform fails borland c++ builder curl_easy_perform fails borland c++ builder](https://i.ytimg.com/vi/rT7faU_rW3Y/maxresdefault.jpg)
This is the start of an application note about range and depth sensors